Plan of Twin City Rapid Transit streetcars #1124-1144 as rebuilt for one-man operation. These cars were assigned to Jackson Street, which has narrow clearances.
Design drawing, including a plan and elevation of Twin City Rapid Transit streetcar #1230, rebuilt for double ended operation on the one-mile shuttle that ran with Fort Snelling to the upper post.
Design drawing, including longitudinal and front elevations of the front half of a Twin City Rapid Transit standard streetcar rebuilt for one-man operation.
Design drawings, including plans and elevations comparing the lightweight streetcars Twin City Rapid Transit Company built for the cities of Nashville, Chattanooga and Evansville.
Design drawing, including plan, elevation and section of the lightweight streetcar built by Twin City Rapid Transit for the city of Chattanooga, Tennessee.
Design drawing, including plan and elevation of an older Nashville streetcar, probably used to supply operating dimensions for the group of lightweight streetcars to be built for Nashville. The Twin City Rapid Transit Company built streetcars for other cities including Nashville, Tennessee.
Design drawing, incluidng plan, section and elevation of Twin City Rapid Transit gasoline boat, intended to replace the steam powered Lake Minnetonka express boats. This boat was never built.
Design drawing, incluidng plan and elevation of an early Twin City Rapid Transit double truck wood streetcar, rebuilt to operate "one-man" (with only a motorman and no conductor). This particular rebuild remained on the drawing board only and was never implemented.
Design drawing, including a plan, section and elevation of a switch car - locomotive built by Twin City Rapid Transit for the University of Minnesota, to be used on the Inter-Campus line.
Design drawing, including plan, elevation and section of Twin City Rapid Transit Sand Car, 43-45 series. These cars were used to sand the rails for adhesion in ice and snow.
Design drawing, including elevation and section of bracket and curtain fixture details of a Twin City Rapid Transit experimental double deck streetcar.
Design drawing, including a plan, section and elevation of Twin City Rapid Transit baggage streetcar #34, which hauled freight and packages to Lake Minnetonka.
This is a general elevation drawing, plus end view of both towers. The suspended car transfer is in the center of the bridge drawing over the canal. Dimensions are included for the distance from the water to the bottom of the bridge span (135 feet) and the footings. The drawing shows small stone and gravel fill near and around the concrete footings at the base of each tower. The finials are shown in detail. Lake Avenue is shown from one tower to the other. Drawing H-5421A, U.S. Patent February 1903.
Contributing Institution:
University of Minnesota Duluth, Kathryn A. Martin Library, Northeast Minnesota Historical Collections
There are three drawn details: end view, part side elevation, lateral bracing in horizontal plane. The towers are the two end parts of the bridge that hold the central span and the suspended car. The towers are referred to as North and South. The South Tower is nearer to Minnesota Point, the North Tower is on the "mainland." Drawing 167, Sheet M11.
Contributing Institution:
University of Minnesota Duluth, Kathryn A. Martin Library, Northeast Minnesota Historical Collections
Technical details and named parts of the suspended car and its supporting structure for the bridge's builders. Included on the drawing are dimensions, rivet poles, braces, center lines, bolt connections, plates, trusses, knee brace, hanger roll. Drawing 161, Sheet M5.
Contributing Institution:
University of Minnesota Duluth, Kathryn A. Martin Library, Northeast Minnesota Historical Collections
Two detailed drawings of the car, or gondola, which carried vehicles and people across the canal. The drawing shows etched glass, punctured decorative steel plates, electric light fixtures, seats with perforated wood bottoms, maple flooring, glass paneled doors, lattice rail, copper flashing, wire supports, wire ropes, dimensions, floor beams, pine planks, and oak flooring. Drawing 162 Sheet M6.
Contributing Institution:
University of Minnesota Duluth, Kathryn A. Martin Library, Northeast Minnesota Historical Collections
A side elevation of the car, or gondola, which carried vehicles and people across the canal. The drawing shows: decorative circular metal plate with the word Duluth and floral-like details, wooden wall with windows, open lattice feature. Plan of strut is drawn as a detail for the bridge builders. Drawing 163, Sheet M7.
Contributing Institution:
University of Minnesota Duluth, Kathryn A. Martin Library, Northeast Minnesota Historical Collections
Detailed drawing of the suspended car, or gondola, and the vertical structure that holds it. This is the element that moves from one side of the bridge to the other above the canal. This transfer car could hold vehicles and people. Normal speed of the car was 4 miles per hour; it made the trip in about 1 minute. This drawing includes dimensions of individual structural elements such as braces. Drawing 160, Sheet M4. Turner is identified as engineer, 816 Phoenix Building Duluth.
Contributing Institution:
University of Minnesota Duluth, Kathryn A. Martin Library, Northeast Minnesota Historical Collections
The Claude Turner design for the original Aerial Bridge from 1901. Many companies and designers vied for this project. The bridge was built in 1904-1905. This drawing shows the spires and steel structural detail as well as the concrete footings and dimensions. Both towers are shown with an end view. In 1929 the suspended car transfer was eliminated and a lift span was installed.
Contributing Institution:
University of Minnesota Duluth, Kathryn A. Martin Library, Northeast Minnesota Historical Collections